Aviator
Cat-eye
Square
Oval
Rectangular
Round
Years of industry experience
Designed to Reflect You
Global Eyewear Brands’ First Choice in Manufacturing
Home / All / Sports Glasses / Anti-Impact Anti-Collision Sport Glasses for Basketball Football Training
Anti-Impact Anti-Collision Sport Glasses for Basketball Football Training
Detail Information
Sport eyewear built around the lens, with a front that supports it under impact.
Overview
A sport frame built for play: the eye is covered at the edge as well as the front, the nose piece keeps the frame off the lashes, and the temple grips instead of sliding. The front is made in the specified compound; the lens specification is an impact-resistant shield lens with the tint confirmed at order. Supply is aimed at team-sports retailers, school and club programmes, and OEM buyers adding an active line to an existing optical range.
The commercial case is straightforward: one tooling set, one colour standard and one packing specification, so a buyer can extend the range by adding colours rather than by adding moulds. The catalogue lists this model under five search terms: sport glasses, anti-impact, anti-collision, basketball football and anti-collision sport glasses. They cover platform, fit and frame family, and all five resolve to model OP178115, so a request placed under any of them reaches the same tooling and the same specification sheet.
Key Features
The four points below are the ones buyers usually test on a sample: material behaviour, fit geometry, optical performance and the customisation boundary.
Frame Material and Impact Behaviour
The front is moulded as a single piece so the shape holds through the run, and the temple is fitted as a separate assembly at the hinge block. Material grade is fixed at sampling against the flexibility and impact target the buyer sets, and the approved grade is recorded, so a reorder is produced from the same compound rather than from whatever is available.
Retention and Fit Under Movement
The temple is shaped to hook behind the ear and is fitted with a grip section, so the frame stays put when the head moves. Venting at the brow keeps air moving, which is the difference between a shield that stays clear and one that fogs in the first minute.
Lens Coverage and Glare Control
The shield covers the eye at the edge as well as the front, which is where grit and glare usually enter during play. Coverage is set by the front curvature, so the protection is a property of the frame rather than of an add-on.
Colour, Logo and Packing
Colour is matched to an approved swatch before production, and the logo is applied at a stage that suits the material: moulded in, pad-printed or laser-marked. The minimum order quantity is 300 pieces, which is the point at which a colour run becomes practical.
Product Showcase
Photographs below are the approved sample set for model OP178115: front, angle, temple detail and colour reference. They are the images used for buyer approval, so a reorder is matched against the same reference.
Specifications
Values below come from the product file for this model. Where a field is not fixed in the file, it is marked as confirmable rather than filled with a nominal figure.
| Model No. | OP178115 |
|---|---|
| Category | Sports Glasses |
| Frame Material | Confirmed at quotation stage (grade fixed at sampling) |
| Lens | Impact-resistant shield lens; tint confirmed at order |
| Colour | Colour range confirmed at quotation stage |
| Customization | Logo and colour customisation supported |
| MOQ | 300 pieces |
| Certification | CE, FDA |
| Packing | Packing configuration confirmed at quotation stage |
OEM & ODM Customization
Customisation is handled at the tooling and sampling stage rather than at packing, because colour and geometry decisions made late are the ones that create a mismatch between the approved sample and the bulk. The list below is the working boundary for this model: anything inside it is quoted as a variant, anything outside it is quoted as a new development.
- Front colour matched to a Pantone or physical swatch before moulding, with a colour chip retained for the reorder.
- Logo applied by moulding, pad printing or laser marking, depending on where the mark sits and how the material takes ink.
- Lens specified at order: tint, coating and, where the brief calls for it, blue-light filtering.
- Temple length and tip curvature adjusted at sampling so the frame fits the target market rather than the sample head.
- Packing configured to the buyer brief: polybag, pouch, case, carton count and barcode label.
Manufacturing & Quality Control
Production runs through four checkpoints, and each one can stop a batch. The sequence is the same for a trial order and for a repeat run, so a buyer who approves a sample knows which checks the bulk will pass through.
1. Incoming Material Inspection
Resin, sheet and temple wire arrive with a batch record. Colour is checked against the approved swatch under daylight, and magnetic inserts, where the model uses them, are tested for pull before the batch is released to moulding.
2. Moulding and Frame Assembly
Front and temple come off the tool, are trimmed, then matched as a pair. Hinge screws are set to a fixed torque and thread-locked, so the fold tension is the same on the first frame and the last.
3. Surface Finishing and Optical Check
Surfaces are polished and, where specified, coated. Each frame is checked for sink marks, colour step at the hinge and lens seat flatness, and a sample is measured against the approved geometry.
4. Packing and Pre-Shipment Sampling
Packing follows the approved carton configuration, and each carton carries a model and colour label. A sampling check is run on finished cartons for hinge tension, colour and logo position before shipment is released.
The full inspection standard is described on the quality control page, and prototype lead times are set out under rapid prototyping.
Applications
Model OP178115 is ordered by buyers in the following channels. The list is not exclusive, but it describes where the shape, price point and packing have already been placed.
- Team-sports retailers supplying clubs and schools
- Safety distributors adding an impact-rated frame to a catalogue
- Outdoor and cycling buyers who need coverage at the edge
- Promotional programmes for tournaments and events
- Private-label sports brands building an entry-level shield
- Online sellers who need a frame that survives shipping and returns
For the wider assortment built on the same specification, see the sports and sunglasses range.
FAQ
What is the minimum order quantity for this model?
The product file records an MOQ of 300 pieces for this model, and that is the quantity a colour run is quoted against. Colour and logo customisation is quoted against the same quantity, so a trial order and a repeat order use one price ladder.
How long does sampling take, and what is needed to start?
Sampling starts once the target colour, logo position and lens specification are confirmed. A stock front can usually be shown from existing samples, while a new colour or a new logo needs a made-up sample. The exact sampling window is confirmed at quotation stage, together with the courier cost and the sample charge, which is credited against the bulk order.
Can the logo and packing be customised?
Yes. Logo support is recorded in the product file for this model, and the mark can be moulded in, pad printed or laser marked depending on the surface it sits on. Packing follows the approved carton configuration, and a buyer can specify polybag, pouch or case before the run is released. Artwork is checked on a proof before production, so a spelling or position error is caught before the tooling is touched.
Start Your Custom Order
Send the activity, the lens specification and the colour count, and the quotation comes back with sampling and packing options. The sports and sunglasses range covers the other protective frames built on the same front geometry. Model OP178115, MOQ 300 pieces, certification CE, FDA. Send the brief and the specification sheet comes back with sampling, packing and price breaks.
Build Your Private Label Eyewear Collection
- *Name
- *Phone
- *Title
- *Content
Why Choose READSUN as Your Optical Frame Manufacturing Partner
New products annually
Countries Exported Products
International Leading Brands Collaborated
Customer Satisfaction
Testimonials
Trusted by Partners Around the World
Products
Ability
